DET NORSKE VERITAS
TYPE APPROVAL CERTIFICATE


CERTIFICATE NO. S-5638

This Certificate consists of 5 pages

This is to certify that the

Windlass

687.50

with type designation(s)

GX2202

Manufactured by

Rolls-Royce Marine AS Dept. Deck Machinery-Brattvåg

ÅLESUND, Norway

is found to comply with

Det Norske Veritas' Rules for Classification of Ships

Application

See Page 2.

Place and date

 

This Certificate is valid until

Høvik, 2009-03-10

 

2013-06-30

for Det Norske Veritas AS

   
     
     
 

Per Arild Åland

 

Local Office

 

Bin Xu

 

Head of Section

 

Surveyor

Product description

Rolls-Royce Marine AS Windlass - Type GX2202

Manufactured by

Rolls-Royce Marine AS, dep.:Deck Machinery - Brattvaag, 6270 Brattvåg Norway

Responsible DNV Station: DNV Ålesund

Rolls-Royce Marine Poland Sp.z o.o., U1. Kopernika 1, 83-140 Gniew, Poland

Responsible DNV Station: DNV Sopot

Responsibility

The holder of Certificate takes responsibility that both design and production are in compliance with Rules, Standards and/or Regulations listed on page 1 of this Type Approval Certificate.

Application/Limitation

The following listed configurations have been approved:

C1

WC1 - C1W

DC1 - C1D

WDC1 - C1DW

C/L motor - C/L cable

Lifter (=max) [mm]

Max allowable chain dia. And grade [mm]

MBL - chain

[kN]

1692

Ø32 K3

833

1292

Ø34 K3

937

The following listed configurations have been approved:

C2

WC2 - C2W

DC2 - C2D

WDC2 - C2DW

It is allowed to mirror cable lifters between bearing blocks.

C/L motor - C/L cable lifter (=max) [mm]

C/L bearing block - C/L bearing block [mm]

Max allowable chain dia. And grade [mm]

MBL - Chain

[kN]

No limitation

584

Ø34 K3

937

The following listed configurations have been approved:

C2DC1 - C1DC2

This is a combination of the two configurations mentioned above, and must be seen separately.

Cable lifter nearest to the hydraulic motor:

C/L motor - C/L cable

Lifter (=max) [mm]

Max allowable chain dia. And grade [mm]

MBL - chain

[kN]

1692

Ø32 K3

833

1292

Ø34 K3

937

Cable lifter second to the hydraulic motor:

C/L motor - C/L cable lifter (=max) [mm]

C/L bearing block - C/L bearing block [mm]

Max allowable chain dia. And grade [mm]

MBL - Chain

[kN]

No limitation

584

Ø34 K3

937

Type Approval documentation

Tests carried out

The windlass is approved based on submitted documentation. Thus only the prime mover needs to be shop tested for required lifting force, reference Pt.3, Ch.3, Sec.3, F105 and F302.

Marking of product

Each windlass is to be marked with manufacturer's name or trademark and type number identification.

Certificate retention survey

For retention of the Type Approval, Det Norske Veritas representative shall carry out biennial Product Audits if regular certification no longer takes place.

END OF CERTIFICATE


Notice: This Certificate is subject to terms and conditions overleaf. Any significant change in design or construction may render this Certificate invalid.

If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such person for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum compensation shall never exceed USD 2 million.In this provision "Det Norske Veritas" shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers, employees, agents and any other acting on behalf of Det Norske Veritas.


DET NORSKE VERITAS AS · VERITASVEIEN 1, 1322 HØVIK, NORWAY · TEL: (+47) 67 57 99 00 · FAX: (+47) 67 57 99 11